The following is a summary overview of the false eyelash curling machine video:

Machine Operation Guide

1. Initial Setup

Position Components:

Place the round tube (also referred to as a circular pipe) on the right side of the machine.

Place the paper on top of the machine.

Place the false eyelashes on the left side of the machine.

Power On:

Locate the power switch under the machine.

Rotate the power switch to the right to turn on the machine.

Wait for the machine to fully enter the system (this may take a moment).

2. Starting the Machine

Reset the Machine:

Press and hold the reset button for 2 seconds.

The machine will enter a reset state.

Wait for the indicator light to turn on, confirming the reset is complete.

Start Operation:

After reset, the reset light and machine start-up light will illuminate.

Locate the start button and press it to begin operation.

The conveyor belt will start running once the start light turns on. Wait for this light before proceeding with further operations.

3. Setting the Pressure

Adjust Pressure Based on Components:

The pressure must be set according to the size of the round tube and the type of false eyelashes.

The machine supports pressure settings from 0 to 4000 units; higher values mean higher pressure.

Example Settings:

For tube number 4:

Set pressure to 4000 (or adjust based on eyelash type).

Click save (long press the save switch) to store the setting.

The display will show tube 4’s pressure as 4000.

To reduce pressure (e.g., to 2000):

Modify the value directly, then long press the save switch to update it.

Switching Tubes:

For tube number 5, set pressure to 2000, save it, and the machine will display this value when tube 5 is selected.

Switching back to tube 4 will show its saved pressure (e.g., 0 or 4000, depending on prior settings).

4. Operating the Conveyor Belt

Debug Page Access:

Enter the debug page using the password 888888.

Conveyor Belt Controls:

JOG Switch: Press to move the conveyor belt a set distance (for precise adjustments).

Continuous Operation Switch: Press to keep the conveyor belt running continuously.

Stop Button: Press to halt the conveyor belt.

Reverse Rotation Switch: Press to move the conveyor belt in reverse, then stop it with the stop button.

Adjusting Alignment:

If the conveyor belt shifts to one side during operation, adjust the two screws at the back of the machine to realign it.

5. Machine Interface Navigation

Main Page:

Displays:

Total production quantity.

Single-shift production quantity.

To clear quantities, long press the clear button/switch.

View production history with password 888888 to see past records.

Production Quantity per Box:

Set the desired production quantity per box.

The machine will remind you when this quantity is reached and automatically reset afterward.

Tube Selection:

Input the tube number (supports diameters from 4mm to 24mm).

Set and save the corresponding pressure for each tube (as described in step 3).

6. Restricted Parameters

Do Not Modify:

Conveyor belt speed: Factory-set; avoid changing.

Conveyor belt movement distance: Pre-calibrated; do not adjust.

Coil pipe conveyor belt speed: Factory-set; leave as is.

Compression motor rotational speed (lower and upper speeds): Factory-set; modification prohibited.

Slight Adjustments Allowed:

Coil pipe distance: Can be tweaked slightly if needed.

7. Additional Features

Production Resume:

Access with password 888888.

View previous production records.

Debugging Page:

Access with password 888888.

Adjust the transfer motor rotation (forward, reverse, continuous) and pressing motor stepping/jointing during setup.

Includes a stop switch for halting operations.

These settings are typically factory-set and should not be altered unless debugging.

Key Notes

Setup Sequence: Always place the round tube, paper, and false eyelashes in their designated positions before powering on.

Pressure Customization: Tailor pressure settings to the tube size and eyelash type, saving each configuration for efficiency.

Conveyor Belt Maintenance: Monitor alignment and adjust screws as needed to prevent operational issues.

Restricted Settings: Avoid modifying factory-set parameters to maintain machine integrity.

Password: Use 888888 for accessing debug, production history, and resume features.

This guide provides a complete walkthrough for operating the machine safely and effectively, ensuring proper setup, parameter configuration, and production monitoring.